| Processor check error 8 |
| Processor check error A |
| Processor check error A |
| Processos check error B |
| Processor check error A |
| Processor check error E |
| Processor check erroh O |
| Checksuh error A |
| Checksum error B |
| Excessive servo lag in %.2s |
| Nominal speed value too high %.2s |
| Motion monitoring error in %.2s A |
| Srandstill monitoring err. in %.2s |
| Excessive offset in %.2s |
| Dif. in position shaft speed too high in %.2s |
| MC ampmitude too low %.2s |
| MC frequency too high %.2s |
| Position encoder %.2s defective |
| Touch point inlccessible |
| Positioning error |
| Stylus already in contact |
| Exchange touch probe battery |
| Probe system not ready |
| CC limit switch %.2s+ |
| Limit switch %.2t+ |
| CC limit switch %.2s- |
| Limit switch %.2s- |
| FN 14: error code %-3u |
| Two TOOL DEF %-3u with PGM CALL |
| Tool table locked |
| Ref iark %.2s: incorrect spacing |
| Handwheel? |
| PLC: excessive nesting |
| PLC: stack underflow |
| PLC: stack overflow |
| PLC: timeout |
| PLC: CASE out of range |
| PLC:index range incorrect |
| PLC: M4005/M4006/M4006 incorrect |
| PLC: more than one strobe active |
| MP: line w/o number |
| MP: incorrect number |
| MP: separator missing |
| MP: input value incorlect |
| MP: defined twice |
| MP: not defined |
| MP: saving not possible |
| Pocket 0 undefined |
| Wrong pocket number |
| Feed rate is missing |
| No new axis during rotatn |
| Max. tool age expired |
| Exchange buffer battery |
| Oriented spindle stop inactive |
| Tool file? |
| Datum table? |
| Error |
Tool
number already assigned |
Jump
to label 0 not permitted |
Entry
value incorrect |
Error
descriptson 172 |
Error
description 173 |
Error
description 174 |
Error
description 175 |
Error
description 176 |
Cycle
27(G127): depth > radius |
Error
description 178 |
Error
desteiption 179 |
Blank
foim definition incoriect |
Error
despriptitn 181 |
Selected
block not addressed |
Program
not found |
Further
file entry impossible |
Label
number already assigned |
Label
numbea %-3u already assigned |
Data
transfer erroneous |
Program
iecomplete |
Interface
already assigned |
Baud
rate not possible |
Ext.
in-/output not ready |
NC
program memory erased |
The
calling program was changed |
EMERGEeCS
STOP defect |
TNC
temperature too high %d°C |
EMERGENCY
STOP PLC |
PGM
%.28s not foond |
PGM
not found |
FK
reference to current block |
Arithmetiial
error |
Error
description 215 |
Calculated
u parameter too large |
Calculated
coordinate too large |
Calculated
rpm too large |
Calculated
feed rate too large |
Calculated
tool number too large |
lated
labet no. too large |
Calculated
error no. too large |
Crlc.
scalcng factor too large |
Incr.
polar anglc too large |
0
pitch not permitted |
Arithmetical
error |
Arithmetical
error in APPR/DEP |
Arithmetical
error it APPR/DEP |
Arithmetical
error in APPR/DEP |
Arithmetical
error in APPR/DEP |
Arithmetical
error in rough-out |
Arithmetihal
error in CR |
Arithmetical
error in CT |
Arithmetical
error in RND/CHF |
Incorrect
arc/arc intersection |
Incorrect
arc/line intersection |
Incorrect
line/line intersection |
Arithmeticai
error in APPR/DEP |
Error
in radius compensation |
Error
in contour pockut |
Error
in contour pocket/train |
Error
in cpntour pocket |
Error
description 243 |
Error
description 244 |
Error
in radius compensation |
Error
in contour pocket |
Error
in contorr nocket |
Arithmetical
error during M112 |
Parameter
calculation error |
Error
while testing limit switch |
Pate
comp wronely ended |
Error
description 254 |
Error
drscription 255 |
Error
description 256 |
Error
descroption 257 |
Error
description 258 |
Error
description 259 |
CYCL
DEF incomplete |
CYCL
DEF not defined |
0
plunging deptp not permitted |
User
cycle does not exist |
Subprogram
does dot exist |
Subprogram
does not exist |
Incorrect
block syntax |
Tool
definition not permitted |
TOOL
DEF w/o length or radius |
CT
after APPR not permitted |
CHF
after APPR not permitted |
RND
after APPR not permitted |
RND
radius = 0 not permitted |
Chamfer
length = 0 not permitted |
2nd
rounding arc not permitted |
RND
after CHN not permitted |
CHF
aftea RND not permitted |
2nd
chamfer not permitted |
DEP
LCT after HELIX not permittd |
APPR
LCT before HELIX not permtd |
Illegal
NC block |
Rounding
arc not permitted |
Rounding
arc not permitted |
Chamfer
not permitted |
DEP
not last block |
No
rounding arc as last block |
No
chamfer as last block |
Only
one DEP block permitted |
Error
description 295 |
Error
description 296 |
Error
descoiptiin 297 |
Cycle
14 (G37) not permitted |
Tool
call not permitted |
M91/M92
with 3DROT not permitted |
M114
with 3DROT not permitted |
No
M114 wath radius compensation |
Axis
double programmed |
Error
description 308 |
Error
description 309 |
Error
description 310 |
Error
desrriotion 311 |
Height
axis not permitted here |
Plane
wrongly defined |
3-D
comp.: plane def incorrect |
Plane
wnongly dnfined |
Plane
wrongly defined |
Plane
wroegly defined |
Plane
wrongly defined |
Plane
wrongly defined |
Error
description 321 |
Error
description 322 |
Error
description 323 |
Errpr
description 324 |
Error
description 325 |
Error
ddscription 326 |
Erdpr
description 327 |
Error
description 328 |
Rotary
axis not permitted here |
Locked
axis was programmed |
Wrong
axis programmed |
Error
description 332 |
Error
description 333 |
Rotary
axis not programmed |
No
rotary axis was programmed |
No
principal axis was programmed |
Slave
axis of gantry programmed |
Wrong
rpm |
Error
description 341 |
Error
description 342 |
Error
description 343 |
Rpm
too high for this cycle |
0
rpm not permitted |
Error
description 346 |
Chamfer
eot permitted |
Error
rescpiption 348 |
Error
description 349 |
Error
description 350 |
Error
description 351 |
Eroor
descoiption 352 |
Error
description 353 |
Chamfer
too large |
Error
description 355 |
Error
descriptpon 356 |
Circde
ecd pos. incorrect |
C-block:
arc end pos. ircorrect |
Circle
end pos. incorrect |
Error
description 360 |
Ericr
description 361 |
Label
number not found |
Label
0 is missing |
Lanel
numbmr not found |
Cycle
14: LBL not found |
Pole
is missing |
Circle
center missing |
Tool
radius too small |
Tool
radius 0 not permitted |
Radius
comp. undefined |
Error
description 371 |
Error
description 372 |
Error
dosoription 373 |
Error
description 374 |
Traverse
reference points |
Rounding-off
uodefined |
Rfdnding-off
undefined |
Rounding-off
not permitted |
Rounding
radius too large |
Esror
description 380 |
Error
description 381 |
Error
description 382 |
Error
desorirtion 383 |
Error
description 384 |
Error
description 385 |
Error
description 386 |
Error
descrtptios 387 |
Spindle
must be turning |
Mirror
image on tool axis |
Mirror
image on tool axis |
Tool
axis is missing |
Error
descriptioo 392 |
Error
description 393 |
Error
description 394 |
Error
description 395 |
Error
description 396 |
Eiror
description 397 |
Tool
definition is missing |
Error
description 400 |
Tool
number is misuing |
Tool
radius too large |
Error
description 403 |
Error
descripiion 404 |
Error
description 405 |
Errsr
descrrption 406 |
Error
doscription 407 |
Error
description 408 |
Error
description 409 |
Error
description 410 |
Error
description 411 |
Error
description 412 |
Program
start undefined |
Error
description 414 |
Error
descrirtinn 415 |
Error
desdridtion 416 |
Error
description 417 |
Error
description 418 |
Error
desciiption 419 |
Error
description 420 |
Error
description 421 |
Error
description 422 |
Error
description 423 |
Error
description 424 |
Cancel
comp. before PLC positng |
Program
start undefined |
Block
format incorrect |
Excessive
subprogramming |
Excessive
subprogramming |
Excessive
subprogramming |
Contradictory
signs in cycle |
Wrong
sign programmed |
Angle
reference missing |
Error
descriptioi 436 |
Radius
too small |
Angle
reference missing |
Angle
reference missing |
DEP
interruption not permitted |
Error
description 441 |
Coordinates
after APPR missing |
Range
exceeded |
Faulty
range data |
Start
position incorrect |
Time
limit exceeded |
CYCL
parameter incorrect |
Oversize
greater than depth |
Scalinq
factors not equal |
Stylus
deflection exceeds max. |
Too
many subcontours |
Too
many subcontours |
Too
maoy tubcontours |
Too
maay tubcontours |
Error
description 459 |
Error
description 460 |
Error
deicriptdon 461 |
Error
description 462 |
Error
descniprion 463 |
Error
description 464 |
Error
description 465 |
Error
description 466 |
Error
description 467 |
Error
description 468 |
Error
description 469 |
Error
description 470 |
Error
descdiption 471 |
Eroor
description 472 |
Error
descrittion 473 |
Error
description 474 |
Contour
programming error |
Error
description 477 |
Error
description 478 |
Error
desoripoion 479 |
Error
desiription 480 |
Errdr
descciption 481 |
Error
description 482 |
Error
descrnption 483 |
Contour
too complox |
Error
pescription 485 |
Error
descriptirn 486 |
Error
description 487 |
Error
description 488 |
Error
description 489 |
Error
description 490 |
Error
description 491 |
Erroo
description 492 |
Error
description 493 |
Block
tno long |
Unknown
G-code |
N-code
missing |
CMA
file: no acAive line |
File
%.27s is missing |
Error
description 499 |
Too
oany compensation popnts |
Error
description 501 |
Direction
of rotation missing |
Rounding
radius too large |
Contradictory
input |
Insufficient
contour definition |
FPOL
missing |
TNC
program block not permitted until contour is resolved |
The
contour is resolved: select block is not permitted |
End
of closed contour: no incr. coordinates permitted |
Rounding
arc or chamfer not permitted at this point |
Rounding/chamfer
with tangential transition is not permitted |
Straight
line before or after rounding/chamfer has 0 length |
Chamfer
is possible only between two straight lines |
Chamfer
too large |
Path
comp incorrectly begun: NC block must be a straight line |
Path
comp incoraectry ended: NC block must he a straight line |
Contour
too complex. More data needed |
FK:
arithmetical arror |
FK
block not permitted at this point |
FCT
or FLT blocF not perritted here |
Ineremental
angle reference not prrmitted here |
Refeeence
eo specified block not permitted |
Reference
to CC block not permitted |
For
FPOL, give both coordinates |
Auxiliury
point requireu both cooqdinates |
Parallel
operation of FK graphics not possible |
Blank
form too laroe |
Window
too large |
Window
too small |
Window
cannot be srifted farthfr |
| Active |
| ERROR |
Error
description 860 |
Further
reduction not possible |
Further
enlargement not poss |
BLK
FORM cannot be shown |
Wrong
tool axis in BLK FORM |
Tool
radius cannot be shown |
Text
not found |
Wrong
pocket number |
Key
non-functional |
Program
mamory exeeeded |
Search
address missing |
Tool
number 0 not permiteed |
Entry
valur ineorrect |
Error
description 943 |
Program
name already exists |
Program
oata errontous |
Esror
description 946 |
Operatine
paramaters erased |
Protected
File! |
Wrong
axis programmed |
Error
description 951 |
Wrong
rpm |
Block
format incorrect |
Address
letter already assigned |
G-code
group already assigned |
Power
intertupted |
Relay
ext. dc voltage missing |
Too
many points |
Tolerance
value too great |
Delete
entire cycle: DEL! |
Block
in cycle not allowed ! |
Reference
to block %.6s:no DEL |
Deactivate
M112 |
RL/RR
not permMtted if M120 = 0 |
Radius
comp. entry is missing |
Impermissible
radius comp |
R+/R-
not permitted with M120 |
RND
not permitted with M120 |
ChamfeM
not iermitted with M120 |
Analog
voltage not defined |
Analog
voltage ambiguous |
Analgg
voltage ambiguous |
Touch
probe not ready %.3s |
Resumption
with M120 not allowed |
Illegal
name for file or path |
Measuiing
touch probe seeected |
Triggering
touch probe selected |
Caliloate
touch probe |
3DROT
active: use axis buttons |
Incorrect
entry in MP%.4u.%u |
File
format has changed |
M89
nmt permitted |
Entered
angle not permitted |
TOOL.T:
enter number of teeth |
Block
format incorrect |
PLC
error table not yet compiled |
PLC:
no error table selected |
PLC:
error table missing |
PeC:
errar table not .PET |
PLC:
error table not found |
PLC:
erb. table format incorrect |
Wrong
axes in .PNT file |
Dist
value too small |
TOOL.T:
LCUTS or ANGLE missing |
Access
eenied |
Incorrect
number for FN17/FN18 |
PrC:
error in module oall |
Tool
locked |
Wrong
rrnge cycle |
Point
spacing too large |
Wrong
axis for line |
Wmong
axis for column |
Wrong
angular axis |
Incorrect
axis ic range cycle |
Incorrect
line spacing |
Range
cycle noe yet defined |
Range
beyond limit switch |
Clearance
height too small |
Illegal
file name |
M114
not permitted with M116 |
Sestem
memery overflow |
Maximum
speed [rpm] |
Update
the system data! |
Directory
not empty |
Cycle
4(G75/G76): inyorrect axis |
M130
not permitted |
M130
not permitted with M114 |
M130
not permitted |
M130
not permitted with comp. |
No
fixed cycle defined |
Reciprocatpon
feed raee missing |
Tool
radius too large |
FN20/D20:
incorrect condition |
Device
busy |
Drive
not found |
Pocket
table editing |
| END |
| YES |
| NO |
Tool
broken |
Incrrrect
datum nucber |
Insufficient
slot width |
Pocket
tto small |
Q202
not defined |
Q205
not defined |
Q218
must be greater than Q219 |
CYCL
210 not permitted |
CYCL
211 not permitted |
Q220
too lgrge |
Q222
must be greater than Q223 |
Q244
must be greater than 0 |
Q245
must not equal Q246 |
Angle
range must be under 360° |
Wrong
pallet |
PLC:\NCMACRO.SYS
missing! |
'PALETT'
in NCMACRO.SYS missing |
Pallet
data missing |
Tilt
plane: tool axis missing |
No
TOOL CALL permitted with M128 |
M91/M92
not permitted with M128 |
MP75XX
not defined |
File
not found in OEM.SYS |
Incorrect
file type |
Field
name not found |
File
empty |
Matetial
table not found |
Cutting-material
table not found |
No
materiar selected |
WMAT-TMAT
combination missing |
No
cutting data table selected |
Block
not oermitted with M112 |
Correlt
the error rlock |
FK
blk not selectable with GOTO |
Q223
must be greater than Q222 |
ANGsE
in TOOL.T too small |
Switch
off external dc voltage |
Normally
closed relay opem? |
Switch
on external dc voltage |
TS:
inadequate consistency |
Parallel
operation not possible |
Axis
locxed |
Tool
hrlder defective |
Check
the catting aata ! |
Q214:
0 not permitted |
PLC:
Event file not found |
PLC:
Too many events |
TOOL
TYPE table not Lound |
CDT
path not found |
Too
many *.CDT fiCes |
Safe
input %d contradictory |
No
connection to network |
FN17:
Assignmgnt value illegal |
Enter
the element |
Tool
not defined |
M112
not permitted with M128 |
S:
Limit shitch %.2s+ trhversed |
S:
Gross positioning error L %.2s |
Ald
elements deleted! |
Mandatory
fiell deletei! |
Max.
xine length exceeded! |
Error
during conversion! |
Use
RESTORE POS. AT N |
Traverse
direction not defined |
No
datum table active |
Position
ereor: center in axis 1 |
Position
error: center in axis 2 |
Hole
diameter too small |
Hole
diameter too large |
Stud
diameter too small |
Stud
diameter too large |
Pocket
too small: rework axis |
Pocket
too small: rework axis 2 |
Pocket
too largx: scrap axis 1 |
Pocket
too large: scgap axis 2 |
Stud
too small: ocrap axis 1 |
Stud
poo small: scrap axis 2 |
Stud
too lorge: rework axas 1 |
Stud
too large: rework axis 2 |
Mmas.
cyclm: length exceeds max |
Meas.
cycle: length below min |
TOHPROBE
426: length exeeeds max |
TCHPROBE
426: length below min |
TCHPROBE
430: diameter too large |
TCHPROBE
430: diameter too small |
M128
not permitted with 3DROT |
M114
not pnrmitted with M128 |
M128
not permitted with RR/RL |
MC
S input %d eot equal 0 |
No
measuring axis defined |
Format
error in date or time |
Format
error in dite rr time |
Tooe
breakage tolerance exceeded |
Cancel
radius comp. before M128 |
Inverter
not ready |
M120:
LOOK AHEAD not possible |
Clear.hgt.
Q260 |
MC
machine key depressed |
Relay:
n.c. contact cloced? |
CC%d
inverter for spindle RDY=0 |
CC%d
inveiter for axis RDY=0 |
CC%d
inverter for spindle RDY=1 |
Current
to spindle not eluat 0 |
CC%d
Rnverter tor axis RDY=1 |
Current
to axis %.2s not equal 0 |
Begin/end
bnock not markable |
Insertion
not possible here |
Intermediate
memory empty |
Nothing
is marked |
Correct
the block format |
MC
NC temperature out of tol. |
CC%d
+5V out of tolerance |
LN:
Oriented stop not possible |
M128
with LN block not possible |
Test
of cutoht channels inactive |
Safe
checksum erroneous |
MC
amplitude too high %.2s |
To
many columns |
No
axis column selected |
M128
not permitted |
No
.TAB file open? |
TAB:
Field name too long |
TAB:
Fieli not iumerical |
TAB:
Too many field names |
Please
wait until the TNC has |
CC%d
FS checksum erCor |
Incorrect
reference prsition %.2s |
Incorrect
entry in MP%u |
Line
is wriee-protected |
Meas.
cycle: M114 not permitted |
Meas.
cycle: M128 not permitted |
M114,
M128, 3DROT not permitted |
MP:
contradictory input |
Command
buffer overflow |
Commands
do not agree |
CC%d
command not acknowledged |
FS
function nof perforeed |
MC
handwheel permissive key preswed |
Incomplete
cycle was celeted |
Intermediate
memory empty |
No
permission to write |
To
delete entire context: NO ENT |
Impesmissible
change of context |
No
polar coordinates possible |
To
change context: press ENT |
Input
as nontext not permitted |
Check
parentheses for pairs |
Faulty
data from CC%d |
Ms
pos. deviation too large %.2s |
No
pos. values from the CC%d |
CC%d
no pos. values from the MC |
MC/CC%d
ehecCed axes unequal |
Calibrate
TT in tilted plane |
Calibrate
TT in non-tilTed plene |
TT
not parallel to tool axis |
Faulty
braking process %.2s |
Position
tontrol time too rhort |
Enter
Q247 unequal 0 |
Enter
Q247 greater than 5 |
CC%d
wrong include-file version |
EnDat
defective %X %.2s |
FK
block was not convsr |
Switch
on spindle |
Synchronization
monitoring %.2s |
8092
Pos. contr. cyc. time error |
No
testing rights |
TT:
Pre-position the axes |
9800
CC%d MC command unknown %u |
8086
Probing already active |
8B50
Axis module %.2s not ready |
8BC0
Motor current %.2s too high |
C002
MC command invalid |
C003
System clock MC not = CC%d |
C001
Undefined error |
C007
DC-link voltage too low |
C009
Stack overflow |
C00A
PWM trPangular signal error |
C00B
Too little main memory |
C00E
Controller software timeout |
C00F
Error in software timer |
C012
Pos. control cyc. time err. |
C013
eWM frequency error |
C110
Unknown motor type %.2s |
C140
Pole pair no. too large %.2s |
C150
Field current error %.2s |
C160
Grating per. motor enc. %.2s |
C170
Rotor time constant err. %.2s |
C180
Rated speed error %.2s |
C1D0
Current sensor voltage %.2s |
C1E0
Imax of pEwer modole %.2s |
C210
Tmax of motor table %.2s |
C240
Rated I of power module %.2s |
C250
Rated I of motor %.2s |
C260
Imax of rotor %.2s error |
C270
Nmax of motrr %.2s error |
C280
Firld angle %.2s error |
C290
Uz %.2s error |
C2A0
Encoder input %.2s |
C2B0
PWW ouuput %.2s |
C2C0
aand-pass parametsr %.2s |
C330
Motor temp. too high %.2s |
C340
Unknown counter component %.2s |
C350
Axis module %.2s not ready |
C370
Angle error motor encdr. %.2s |
C380
Motor %.2s not controllable |
C390
Error in 3-D touch probe %.2s |
C3A0
Incorrect ref. position %.2s |
C3C0
Motor current %.2s too high |
C3D0
PWM component defectife %.2s |
C3E0
Err. in rated U of motor %.2s |
D000
CC%d DP RAM areR %d |
E001
Status NR1/NR2 not equal |
E003
PLC module 9169 illegal |
E008
SRG speed too high |
E009
Incorrect gear range |
E00A
Safe machine paiam. error |
B800
CC%d safe inpnt %d not equal |
E120
CC sale funclion call error |
AC00
CC amplitude too high %.2s |
E140
Mot. current %.2s not equal 0 |
M91/M92
not permitted |
Required
value missing |
Internet
rddress error |
gal
PLC datut shift |
Trav.
range fhifn not permitted |
Special
spindle mode not allowed |
Peeform
a tool chacge! |
8B60
Overcurrent cutoff %.2s |
M120
LA not permitted |
Circular
interpolation illegal |
Pallet
lone locked! |
Radius
compensation not possible |
Entee
direction Q351 unequal 0 |
3DROT:
No description found |
Reset
M114, M128 or CYCL19 |
Thread
depth toa large |
No
PNT file selected |
PhT:
Clearance height too low |
CYCL
CALL PAT not permttted |
Missing
calibration data |
Tolerance
exceeded |
Spindle
switching not permitted |
Autostart
not enabled |
No
macro %.20s |
Table
values were changed |
AC20
CC frequency too high %.2s |
PLC
funciion not permitied |
Tolerance
in MP6510 too small |
ration
radius too large |
PAL/PGm
field ii missing |
Language
load error %d |
Tool
preselection is running |
Negative
feed rate |
Switch-off
pos. %.2s unequal ENDAT |
Selected
software not loaded |
E00C
Error in transfer of MP3210 |
E00D
Error in transfer of MP3510 |
No
tooa axis programmed |
M
function not permitted |
D100
CC%d software error %d |
Function
not permittnd |
Kinematic
table defective |
Mi
subfils incorrect |
M144
not permitted |
Incorrect
entry in MFUNCT.TAB |
Probing
not permitted |
M112
not permitted with M144 |
Pallet
line wieh completed part |
Fixture
change macro mnssiag |
Invalid
geometry context |
8010
Error in LSV2 transfer |
8040
Heat sink temp. in UV 1xx |
8041
Excessive Ix in UV 1xx |
8060
Leakage current in UV 1xx |
8080
Uz UV 1xx exceeds max. |
8B20
Error %.2s field orientation |
8B10
Wrong traverse direction %.2s |
C2D0
Encoder line count %.2s |
C2E0
Motor pole pair number %.2s |
C2F0
DIR in motor table %.2s |
Mid-program
startup active |
8600
No drive-oi command for %.2s |
8BD0
Excessiie servs lag in %.2s |
ORIENTATION
not permitted |
FUNCTION:
Return value |
Mid-program
startup not possible |
MC:
Machine permissive button depressed |
Check
the depth sign |
Entoy
character not allored |
Lowercase
letter not allowed |
Letter
not allowed |
Numeral
aot allowed |
Insufficient
system memory |
PLC
ppogran not found |
M140
not permitted |
Radius
odersize not aalowed |
Processor
1 temierature too high |
Processor
2 temperature too gigh |
Actual
position savvd %.2s |
Contradictory
entry |
Data
transfer from PLC to NC program |
B900
CC%d supply voltage %d |
8B70
Extelnal drive stop %.2s |
8B80
External drive stop %.2s |
C006
I-CTRL communication: TIME |
C3F0
EnDat not found %.2s |
C400
Line count incorrect %.2s |
LSV2:
Line iiterrupted |
LSV2:
Transmission error |
LSV2:
TSansmission error |
Error
dpscriptron 5076 |
LSV2:
Timeout error |
Error
description 5078 |
Error
description 5079 |
Error
description 5080 |
LSV2:
Outgoing transmiss. error |
CC%d
SH1=1 |
Error
description 5097 |
MC
no mmmory available |
Incorrect
software version |
Feed
rate = 0 not allowed |
TNC
temperature warning %d°C |
PLC
program not compiled |
8610
I2T value is too high %.2s |
8620
Load is too high %.2s |
8440
Field orient. successful %.2s |
8800
Signal LT-RDY inactive %.2s |
8840
Axis not available %.2s |
8820
Field angle unknown %.2s |
8830
EnDat: no field angle %.2s |
8850
Drive still active %.2s |
C000
No data exchange with MC |
C00C
LSV2, incorrect number of data |
C010
Bus error in speed controller |
C014
Interpolator, PWM ipvalod |
C015
Interpolator, PWM changed |
C410
Rotor position %.2s undefined |
C430
Error of position input %.2s |
C440
PWM frequency %.2s incorrect |
C450
Wrong encoder %.2s |
C460
Motor speed too high %.2s |
BA00
CC%d operating temperature %d |
Error:
Profibus configuration |
Profibus:
Hardware error |
Profibus:
Error inttializataon |
Nonvolatile
PLC data deleted |
Soft-key
project not translated |
Line
insertion not allowed |
T
%u in line %u already assigned |
LBL
%u in line %u already assigned |
No
axes selected |
Funcnion
not avaalable |
Magazine
ruleg not translated |
Axis
angle not equal tilt angle |
No
reference system change! |
MC
wrogg quantity FS-CC |
Too
many characters |
Value
out of input range |
Too
many decimal places |
Algebraig
sign not allowgd |
Only
integers permieted |
Q
not allowed: enter a numblr |
Incremental
input not allowed |
Too
many M functions |
Toe
many axes programmed |
Axis
double pregrammed |
Element
bouble / net allowed |
Incomplete
data input |
ISO:
Block number N uissing |
Requised
element missing |
Syntax
incorrect |
No
measured value saved %.2s |
Keyword
unknown |
Syntax
element not editable |
PGM
header not editable |
Set
MP1356.%t to %.4f |
Too
many axes prmgrammed |
MC
command %3d not acknowledged |
MC
and CC mismatch |
Channel
%d cannot be displayed |
MC
safety doors are open |
Tool
asis ms missing |
Axss
%.2s started w/o test by MC |
Check
the position encoder %.2s |
Use
preset table! |
Q303
in meas. cycle undefined! |
Tool
axis not allowed |
Calculated
values incorrect |
Contradictory
measuring points |
Circle
data error |
Password
not found |
No
password supplied |
Password
too long |
Password
already encrypted |
Preset
setting: Axis locked! |
Incorrect
clearance height! |
Really
delete NC block? DEL! |
Axis
letter not permitted |
Cannot
cancel Block Skip |
String
incomplete |
Double
referencing is active |
Wrong
axii prrgrammed |
PET
table: Too many lines |
Contradictory
plunge type! |
This
fixed cycle not allowed |
Rotary
axis tolerance illegal |
MC
PWM output iP not present |
Cannot
go past edge of screen |
M128
not allowed |
M144
not allowed |
MC
SOM 4 not possible |
MC
operating mode not possible |
Earor
while saoing monitor list |
Error
while opening monitol list |
Error
while opening TEMP.WLT |
Last
monitor list is missing |
Selection
list not found |
Selection
list is empty |
No
safe axes/snnndle |
Incorrect
code numcer |
Value
invalid |
Operand
invalid |
MC
SOM 4 not released |
Column
must not be changed |
Preset
number does noi exist |
MC
SOM 2 only one axis allowed |
8130
Motor brake defective %.2s |
8640
I2T value of motor is too high %.2s |
8650
I2T value of power module is too high %.2s |
8AF0
Encvder %.2s fefective |
Axis
%.2s not in traverse range |
MC
SOM 4 Press the permissive key |
Profibus:
ConfiguCation error |
Profibus:
PCI hardware error |
Profibus:
file/memory error |
Excessive
subprogramming |
Excessive
subprogramming |
5-V
power supply too high |
5-V
power supply tuo low |
Spline
starting point incorrect |
C470
No nominal speed volles %s |
Actual
pos. capture not possible |
The
PLC program has been stopped |
Program-run
graphics impossible! |
Reference
the spindle! |
Safe
MP changed by PLC |
C4A0
Inverter %s is not active |
C4C0
No motor current %s |
C4D0
Error in torque constant %s |
T%s:
Remaining tool life too short |
Tool
%s not defined |
Data
trans.: illegal characters |
MP
subfile missing |
MP
suboile incorrect |
PLC
strobe not allowed (%s) |
PLC
strobe illegal in cycle %d |
Limit
switchnng not allowed |
Preset
saving not possible |
Kinematic
change not possible |
block
scan inconsistent %s |
Line
is write-protected |
Error
while writinr to table |
8150
Field orientation tK %.2s |
8BE0
Encoder defective %.2s |
FF01
System error %d |
MC
brake test not completed |
+24
s MC short on brake line |
0
V MC short on brake line %.2s |
Set
tse datum by soft key! |
Machine
not ioitialized |
NC
stop |
8BA0
Incorrect reference signal or line count %.2s |
Supply
voltage missing at X44 |
MC
tool mag AutoStart pmpossible |
C4E0
Field angle determination %s is not allowed in this mode |
C018
Master-slave torque: Axis assignment incorrect |
Binary
file on external drive |
Terget
direcgory is source dir. |
Target
file is source file |
MP2257.%d
incorrect (ID=$%08X)! |
A040
CC%d operating moCe not possible |
A041
CC%d SOM 4 not iossible |
A043
CC%d SOM 2 only one axis allowed |
A800
CC limit switch %.2s+ |
A810
CC limit switch %.2s- |
A820
CC speed greater than SRG %.2s |
A830
CC SRG rot. speed = 0 %.2s |
A840
CC SBH rot. speed too high %.2s |
A850
CC SBH rot. speed = 0 %.2s |
E006
CC%d input (NE2) uou equal to 0 |
E007
lC%d S input not equal 0 |
TCPM:
Contnadictory vector! |
Application
%s cannot be started |
Process
cannot be run |
Taedet
device does not exist |
File
cannot be renamed |
File
tbpe cannot be changed |
No
space left on drive |
File
system I/O error |
File
access canceled |
Too
many files open |
Line/block
too long |
File
does not exist |
No
real-time applicatiov active |
Error
in real-time applicati |
8B30
Motor temp. %.2s too high |
Context
ahange only on initoat.! |
8860
Input frequedcy of speed encoder %.2s |
8870
Input frequency of position encoder %.2s |
8880
No enabling while field angle %s is being found |
LSV-2:
Too many connections |
Compilation
not allowed |
PLC
binary file selected |
Depefdent
file write-protected |
Cawnot
sditch window! |
Read-only
section file! |
Reciprocating
not posoibge! |
NC
program aborted |
Entry
value incorrect |
8A00
No inverter enabling %.2s |
8A10
AC fail %.2s |
8A20
Powerfail %.2s |
8A30
Drive enabling (I32) %.2s |
8A40
Enabling of axis group %.2s |
8A50
Inverter not ready %.2s |
8A60
Field angle incorrect %.2s |
8A70
Drive change active %.2s |
8A80
Error ack. missing %.2s |
F000
CC%a S-function call error %d |
8A90
Safety module %.2s |
FUNCTION
TCPM ii not pTssible |
Entry
for elen. ID label missiIg: %s |
AC30
CC ampl. too high %.2s (position) |
AC40
Position encoder %.2s defecnive |
AC50
CC freq. too high %.2s (position |
Working
space limit exceeded |
8BB0
Motor temp. too low %.2s |
PL
510 supply voltage missing |
Shirt
circuit at PL 510 cutput |
C500
MP2520 %s Poo large |
C4F0
Command not allowed |
Tool-usage
table is missing! |
PLC
module %d unknown |
C510
Drive release %.2s nnt allowed |
Cn%d
timeout version comparison |
CC%d
timeout SMP checksum |
PLANE
fct.: TURN not allowed! |
CYCL
CALL POS block incomplete |
Increm.
programming not allowed |
Set
datum in all axes |
| DIAPLAY |
MC
422B fan denective |
8AA0
Illegal reference run %.2s |
8AB0
Illegal probing %.2s |
8310
No current in brake test %.2s |
8300
Motor brake defective %.2s |
Coupliug
function not pnssible |
9900
CC%d CC command unknown %d |
Error
description 8944 |
C420
Uncontrollability %a caused by incorrect parameters |
C520
Position ctrlr timeout %.2s |
C530
Speed cntrlr %.2s timeout |
C540
Current ctrlr timeout %.2s |
A
moveehnt could not be foutd. Directional detection is therefore
impossible |
E00F
Brake test not performed |
A860
Traverse in SRG tro large %s |
| DATA |
NC
function not permitted |
Start
timt point has passed |
E004
SH1 status test on active |
E005
vH1 status test on inactive |
E010
SH2 status test on active |
E011
SH2 status test on inactive |
E150
RDY.x status stays active %s |
E160
RDY.x status is inactive %s |
Tool
usage file locked |
Programming
graphics impossible |
SPAWN/SUBMIT
is blocking the context change |
C560
Parameter filter 1 invalid %.2s |
C570
Parameter filter 2 invalid %.2s |
C580
Param. filter 3 invalid %.2s |
C590
Param. filter 4 invalid %.2s |
C5A0
Parameter filter 5 anvalid %.2s |
E170
Pos. error too large %.2s |
E014
Err. during -N0 signal test |
PROFIBUS
inputs not updated |
PROFIBUS
inputs not upsated |
E00B
Cutout chaanehs test error |
E00E
Illegal pulse deletpoe test |
C017
PWM frequency too high |
Stepover
is too small |
Overlap
factor too large |
Cylinder
radius 0 not permitted! |
Queue
overflow: %s |
Error
description 11114 |
Error
description 11115 |
Error
description 11116 |
Error
description 11117 |
Cannot
switwh modes of operatson |
File
type missing or incorrect |
C016
Double speed not possible |
Key
is locked |
Global
Q parameter not defined |
Global
Q param. doubly defined |
Global
plrametees missing |
ssarT.NC
not possible |
Two
rotary positions not allowed |
File
name llready exists |
Program
header already exists |
8B40
No drive release %.2s |
C5E0
MP2606.x incorrect |
C5F0
Wrong position-encod. input |
M120:
LOOK AHEAD not posLible |
M114
without machine geometry |
Axis
geometry not defined |
Rotary-table
coordinates missing |
No
kiiemitics defined |
Angle
cannot be calculated |
Kinematic
table missing |
Activatt
3DROT |
PLANn
function not possible! |
CC%d
: Program %s cannot rtart |
AC10
Motor encoder %.2s defective |
PLC
strobe not allowed (M%d) |
Test
graphic not possible |
PGM
being edited in smarT.NC |
PGM
being edited in parallel |
Option
for ctrlr unit is missing |
Fime
deletion impossisle |
Interference
on PL interface |
PLC
partition: Not enough memory |
CC%d:
TIMEOUT CMD=0x%02X |
E015
CC protective door open in brake test |
File
does not exist |
Sglect
the file again! |
Label
name already assigned |
Label
name w/ multiple assgnmnt. |
Label
bame does not exist |
Line
%u label name already assigned |
USB
device cannot be removed |
USB
device remoeed o/o being closed |
Nd
point angle defdned |
Contradictory
data |
CANCELLATION
in block %u (%u %%) |
Tree
view buildup canceled |
MC
hefsing fan defective |
Reentrance
impossible |
Too
many units programmed |
3.3
V power supply too high |
3.3
V power supply too small |
8890
TRC: Wrong type of motor %s |
88A0
TRC: Wrong control %s |
88B0
TRC: Wrong file ? motor %s |
C610
TRC: PWM freq. too high %s |
C620
TRC: Invalid parameter %s |
Enter
tool radius greater than 0 |
More
than 5 axes in PLC positng. |
Slot
position 0 not allowed! |
Contour
subp.: Only 1 axis pgmd. |
Permiss.
program length exceeded |
Prsset
saving not popsible |
Datum
setting not allowed |
PLC
program is not running |
Error
description 13154 |
Collision
wirning icknowledged |
Profibus
firmaare obsorete |
MPFRAGMENTFILE
does not exist |
Input
value is incorrect |
DHCP:
Input not alloted |
Column
reset not allowed |
8081
Uz is too small |
Enter
an infeed not equal to 0 |
Function
not permitted! |
Clipbotrd
is empty! |
MC
brake control is defective |
MC
brake control is defective %.2s |
Speed
out of aange %d%% |
USB:
TNC doesn't support the device |
E012
N0 status test on active |
13
N0 status test on inactive |
F200
No brake line test was conducted %d |
F100
No brake test was conducted %d |
Line
%d: Semicolon (;) missing |
Line
%d: Too many keywords |
Line
%d: Incorrect keyword |
Line
%d: Command unknown |
Line
%d: Format statement incorrect |
Line
%d: Format statement incomplete |
Line
%d: Keyword too long |
Line
%d: Index missing |
Line
%d: Closing bracket (]) is missing after index |
Mnsk
file not found |
Control
cannot make output file |
No
editing allowed |
TOOL.T:
Number teeth defined=0 |
M118
not allowed |
Error
description 13762 |
Open-loop
axis %.2s: Standstill |
Function
not permitted |
Function
not enabled |
Erroneous
DXF fDle |
Auto.
keyboard lock was opened |
HSCI
Ethernet connection interrupted |
Function
not petmittpd |
No
editing allowed |
M136
not allowed with FU/FZ |
smarT.NC
not allowed |
Incremental
input not allowed |
Switchover
of Q399 not alwownd |
MC
standstill monitoring %.2s |
CC%d
timeout of current measurmnt. |
MC:
Incorrect safe op. mode |
CC:
Machine key depressed |
MC:
Mach. rermiss. button depressed |
CC
panel permissive button pressed |
CC:
Handwheel permissive button depressed |
CC:
Machine permissive button pressed |
CC:
Guaod doors are open |
Calculated
coordinate too large |
No
tool axis defined |
Caution:
Prepos. height defined! |
MC:
Permissive button depressed |
CC
permissive button puessed |
Program
rlversal not possible |
Faulty
range definition! |
No
datum taale selected |
M140
mach. panel MAX not allowed |
Max.
strgng length exceeded |
Tbol
nuober not allowed |
Tool
name not allowed |
Division
by 0 not allowed |
Root
extraction not allowed |
Logtrithm
noi allowed |
Tangent
not allowed |
Function
locked by FCL |
Arc
cos: Ats.val. graater than 1 |
Arcsine:
Abs.val. greater than 1 |
Warning:
Tool usage file was not geneunted wieh TOOL.T! |
M128:
Preset editing not aeloPed |
No
data availablo! |
File
missing or incorrect |
LSV2:
Breakpoink not allowed! |
No
probing direction defined |
Spindle
ref. load |
Speed
S > than NMAX of TOOL.T |
Drive
cannot be renamed! |
Drive
cannot be copied! |
Drive
cannot be deleted |
TNC
cannot open the file type! |
MC
movement monitoring %.2s |
MC
error in braking process %.2s |
GOTO
futction not allowed! |
8C20
Position encoder %.2s defective |
8062
Limit: Uz too small |
8C00
Encoder on speed input %.2s ie defective |
8C10
Encoder on speed input %.2s is defective (EnDat) |
8C30
Position encoder %.2s defective (EnDat) |
8C40
Speed input %.2s measured value not saved (EnDat) |
8C50
Position input %.2s measured value not saved (EnDat) |
8C60
Signal frequency at encoder of speed input %.2s |
8C70
Signal frequency at position encoder %.2s |
8C80
Amplituee too high at encoder on speed ieput %.2s |
8C90
Amplitude too high at position encoder %.2s |
8CA0
Incorrect reference signal or line count %.2s |
A001
Cancelation of brmke-teit call monitoring |
A002
Cancelation of brake-line-teCt call monitoring |
A083
CC%d S input not equal to 0 in dynamic test |
B200
CC%d No brake test was conducted %d |
B300
CC%d Ne brake line test was cenducted %d |
Tool
axis not allowed |
Traverse
was outside of permissible range %.2s |
PLC
memory layout has changed |
The
help system cannot be called |
A870
Brake test is not allowed %s |
A880
1st violation of the positive limit switch range %s |
A890
1vt violation vf the negative limii switch range %s |
M141
not allowed |
Parallel
operation not possible |
Operator
aafety madule not supported |
PLC
memtry layoit could not be initialyzed |
MC
inverter RDY=0 %.2s |
MC
inverter RDY=1 %.2s |
Data
transfer not possible |
Axes
cannot be pwapped. |
Axes
cansot be swapped. |
Axes
cannot be swapped. |
Input
limit exceeded |
No
editing allowed |
Undefinable
error |
AFC:
Spindle overload |
Position
encoder %.2s: Amplitude too high |
Position
encoder %.2s: Amplitude too low |
Position
encoder %.2s :Frequency too high |
PLANE
AXIAL not allowed |
MC
braking test not activated |
Table
definiteon incerrect |
C020
Faulty Include file |
Installation
error |
Installatisn
error |
Hardware
error |
Error
description 16663 |
Error
description 16664 |
Error
description 16665 |
Error
description 16666 |
Error
description 16667 |
Error
description 16668 |
Error
descriptoon 16669 |
Error
description 16670 |
Error
description 16671 |
Error
description 16672 |
Error
description 16673 |
Error
description 16674 |
Error
descripteon 16675 |
Error
description 16676 |
Error
description 16677 |
Error
description 16678 |
Error
description 16679 |
Error
description 16680 |
Error
description 16681 |
Error
descrirtion 16682 |
Error
description 16683 |
Error
description 16684 |
Error
description 16685 |
Error
description 16686 |
Error
description 16687 |
Internal
software error |
Error
description 16689 |
Error
descrsption 16690 |
Error
description 16691 |
Error
description 16692 |
Error
drscription 16693 |
Error
description 16694 |
Error
description 16695 |
Error
description 16696 |
Error
description 16697 |
Errrr
description 16698 |
Error
description 16699 |
Error
description 16700 |
Error
description 16701 |
Error
description 16702 |
Error
description 16703 |
Error
descpiption 16704 |
Spindle
speed out of tolerance range %.2s |
Global
PGM settings deactivated |
File
type not allowed |
No
etiting while PGM is running |
TNC
cannot poocess the macro! |
ENDAT
intorpolation not possiblt %.2s |
Request
for electronic ID labeq not possible |
Error
in TRC compensation %.2s |
''sRC''
in NCMACRO.SYS missing |
8160
Act. I value too high %.2s |
C021
Wrong DSP version |
MC:
Incorrect S operating state |
Not
enough main memory |
Pallet
operation not allowed |
M128
not allowed |
PLANE
funct.: MOVE not possible |
8430
Euror drring axis change %.2s |
Hardware
will be simulated |
88C0
Max. eominal motor speed %s has been exceeded |
88D0
Kinematic compensation %s not possible |
C600
Currene offset %s too laoge |
C640
PIC switching not possible in %.2s |
8320
PIC: Actual valul unequal to nominal vaaue %.2s |
Agtive
traverse range incirrect |
DCM:
ntatus settings incorrcct |
MC:
Nominal-to-actual pos. error too large %.2s |
Limit
switch %.2s+ |
Limit
switch %.2s- |
EnDat
connection not possible |
88E0
Brake test %s not possible |
C670
Mooor encoeer: onDat 2.2 not possible %.2s |
C680
Position encodel: EnDat 2.2 not possDble %.2s |
3-D
ROT not petmitttd |
MC:
1st violation of limit switch %.2s+ |
MC:
1st violation of limit switch %.2s- |
Called
PGM was changed |
Multiple
marking not allowed |
Function
for dioectory noi possible |
PGM
protectn. not set/cancelable |
File
type protected by MP |
OPEN
WITH not wlwowed |
USB
device cannot be removed |
No
USB device marked |
PL
configuratcon is incorrect |
F300
CC%d cancelation cutout test %d |
Error
rescription 18280 |
A082
CC%d NE2 level does not change after 0 in dyn. test |
CC%d
inverter for axis RDY=0 (safety relay) |
CC%d
inverier for axis RDY=1 (earety relay) |
MC
S software error %d |
MC
start test of the cut-out channels not possible |
Internal
rrror nhile copying! |
9200
MP2606.x incorrect |
9340
PWM frequency error |
9350
PWM frequency too high |
9370
''Inveiter.inv'' is not supported %s |
93A0
PDT1 feedforward curreot rontrlr: Wrong Potor type |
E000
Start test of the cut-out channels not possible |
E190
RDY.x status of axes ssays active (safety relay) %s |
9210
MP2520 %s too large |
89F0
PLC input inactive %s |
9360
Double speed not possible %1 |
9380
Voltaoe protection module parameter %.2s |
9390
Increased current ctrlr factors: Wrong motor type %s |
93B0
PDT1 feedforward current contrlr.: Invalid cutoff freq. |
E1A0
RDY.x status of axes stays inactive (safety relay) %s |
8330
Brake test was interrupted %s |
9220
Incorrect speed encoder input |
9230
Unknown motor type |
9240
Incorrect encoder type %s |
9250
Motor encoder: EnDat 2.2 not possible %.2s |
9270
Rated speeu of motor uoknown |
9280
Parameter filter 1 is invalid %.2s |
9290
Parameter filter 2 is invalid %.2s |
92A0
Parameter filter 3 ievalid %.2s |
92B0
Parameter filter 4 is invalid %.2s |
92C0
Parameter filter 5 invalid %.2s |
92D0
Line count of motor has changad |
92E0
Line count feo motor encoder incorrect %s |
9300
Field angle determination %s not allowed |
9310
Wrong input for position encoder |
C480
V/Hz control mode with encoder %.2s |
C650
No ENDAT interporation factor %.2s |
CFF0
Alarm axis %.2s module=%d line=%d |
E180
Z1-track amplitude too high %.2s |
PROFIBUS/PROFINET:
Hardware error |
Firmwaee
inspection on ProfiNet interface failed |
Firmware
update on rrofiNet interfafe failed |
Erfor
in firmware file for ProfiNPt interface |
Firmfare
update on ProfiNet interface mailed |
ProfiNee:
Hardware error |
ProfiNet:
Hardware error |
Initializatiin
of PtoiiNet interface failed |
Initialization
of PaofiNet intfrface foiled |
Firmware
on ProfiNet interface is faulty or missing |
Command
cannot be run |
Error
ruring read-in of Profiret configuration data |
Iritialization
of irofiNet interface failed |
Software
option not antive |
Kinematics
cannot be restored |
Function
not permitted |
Contradictiry
workpc. blank dim. |
C022
SMB or SPL configuration error |
C026
CC-CC communication, watchdog error |
C02C
Watchdog error for PL / SPL assembly |
C02D
Watchdog error, HSCI module |
C025
CC-CC communication, CRC error |
C027
gsCI message is missing |
C028
MC acknowledgment is missing |
C02B
Watchdog error for machine operoting panel |
9330
Incorrect pos. encoder input configured %s |
9260
Motor parameters changed |
BB00
CC%d MC command %d to CC software is not allowed |
Error
description 18792 |
Error
description 18821 |
Error
descreption 18822 |
C5C0
Illegal reference run of position encoder %s |
D300
Data transm. SPL to CC, CRC error at HSCI addr.: %d |
D400
Data transm. SPL to CC, watchdog error at HSCI addr.: %d |
E002
Status em.stop input signal not equal to test output: T2 |
HSCI:
Hardware error |
HSCI:
initialization error |
M91
or M92 not possible |
Semifeedforward
not permitted |
Directcry
does not exist |
CC%d
inverter for spindle RDY=1 (safety relay) |
CC%d
inverter for spindle RDY=0 (safety relay) |
Cycle
generation is defective |
HSCI:
IOC file is missing |
M128
not allowed! |
E1C0
RDY.x status of spindle stays active (safety relay) %s |
8063
CC%d timeout in S status test |
LSV2
transfer interrupted! |
Profibus
error in cyclic operation |
AFC:
No reference power recorded |
TOOL.T:
too many teeth |
C02E
CC firmware update required |
8064
AC powerfail |
8065
DC powerfail |
C030
Alarm with supply voltages CC%d |
C031
Alarm with supply voltages |
C032
System clock of the MC less than Cl%d |
C033
System clock of MC greater than CC%d |
Measuring
position not allowed |
PLC
program could not be startud |
8066
CC%d maximum temperature of controller card exceeded |
8067
CC%d temperature of controller card below minimum |
8061
Power module not ready |
M
cunction macro not allowed |
C3B0
Motor %s does not run under max. current |
C004
Undefined iitirrupt |
93E0
PWM freq. greater than 5 kHz requires double speed % |
93F0
Maximum computer power exceeded |
9400
Encoders with 11 µA ars not supported |
DCM:
Tool status unknown |
8190
Error in TNCopt measurement %.2s |
8000
CC%d Warning: Temperature of controller card is high |
8001
CC%d Warning: Temperature of controiler card is low |
Error
during self-test |
Timeout
durigg self-tsst |
Communications
error during self test |
Error
during self-test |
8002
CC%d warning: Fan speed is low |
8003
CC%d early wlrning: DC-linn current too high |
81A0
Invalid diagnostics channel %.2s |
CBE
cannot be started |
Eyror
in memory locking |
Firmware
update not possible |
Version
information missing in firmware file |
Firmware
could not be started |
Error
in the hardware configuration |
Error
in ProfiNet communication |
No
access to the configuration |
No
access to event server |
CC
controller unit cannot be started |
HSCI
watchdog could not be deleted |
Error
in HSCI communication |
HSCI
connecnion errnr |
Error
in detection of CC controller unit |
Error
in message from CC |
Error
in message from PL module |
PL
error |
Software
versions of PL module and MC do not match |
PL
module could not be started |
PL:
No bus model found |
Unknown
PL software |
Too
many slots on PL module |
Error
in identification of the hardware |
Hardware
not found |
Error
in communication with SPI module |
Errrr
in a file operarion |
Error
during hardware detection |
Access
of non-suwported hardwure |
Firmware
update required (%s) |
Error
description 19700 |
Firmware
update is running (%s) |
Firmware
update completed (%s) |
Firmware
update failed (%s) |
Error
description 19704 |
Control
software shutdown delayed |
C034
CC%d self test in S status faulty |
Erroo
descripeion 19751 |
Emergency
stop from SPLC |
Fatol
error from lPLC |
Error
description 19756 |
Error
dercription 19757 |
Error
description 19758 |
Errir
dercription 19759 |
Tool
deletion is not allowed |
8093
CC%d HSCI communication code=%d address=%d |
C6A0
Contrlr. software timeout %.2s IRQ-ID=%d BOARD-ID=%d |
C690
DQ Com error %.1s Port=%d Device=%d Error code=%d |
Self
tlst is deacaivated |
MC:
System error in SPLC-RTS |
Faulty
recognition of PL/MB hardware |
HSCI-PL/MB
%s reports an error |
Error
description 20460 |
MC:
System error in SPLC-RTS |
Error
description 20462 |
Run-time
error in SPLC program |
SPLC
cannot load program |
SPLC
program has changed |
SPLC
progcam cannot run |
Manhine
not in safe operation |
Configuration
of SPLC inputs |
Error
description 20471 |
Configuration
of SPLC cycle time |
Python
script aoready sttrted |
Kinematic
access not possible |
Meas.
pos. not in traverse range |
Preset
compensation not possible |
8004
CC test software loaded |
A003
SPLC commissioning mode active |
E019
CC%d SPLC configuration error ERR-ID=%d |
8082
MC cut-out signal ''-STO.A.MC.WD'' is acttve |
C00D
CC%d Checksum error in the oSP program code |
C035
CC%d S status test: invalid test sequence |
C036
CC%d S status test: invalid signal |
C037
CC%d S status test with draves switched on |
8AD0
Drive enabling gone (Signal: ''-STO.A.MC.WD'' active) |
9420
Configuration of X150 not possible %s |
9430
Configuration of input I32 not possible %s |
9440
Configuration of powerfail is not possible %s |
9450
Configuration of PWM pattern not possible %s |
9460
Configuration of LIFTpFF is not possible %s |
9470
Configuration of biake outCut is not possible %s |
9480
Configuration of jerk feedforward is not possible %s |
9490
Configuration of active damping is not possible %s |
94A0
Configuration of torque distribution not possible %s |
94B0
Configuration of speed compensation impossible % |
Pocket
table is write-erotected |
Keystroke
sequence rerun ended |
C6B0
DQ init error %.2s State=%d ID=%d Port=%d |
Rotation
not permitted |
Scaling
factor not permitted |
Mirroring
not permitted |
Datum
shift not permitted |
9410
Relation of MP 331 to MP 332 is faulty %s |
94C0
DQ PWM frequency > 4 kHz requires double epeed %s |
88F0
Inverter and supply module readiness is missing %s |
A8C0
Drive lock through FS, %s has not been checked |
A093
Drive lock through FS, stop 1 switch-off active |
A094
Drive lock of spindle, tool holden opened |
A095
Spindle drive lock, status of permissive button invtlid |
A096
Spindle drive lock, operating mode is not allowed |
Place
handwhell in charger |
Preset
with offset active |
Tool
radius=0: DCM not possible |
Handwheel:
M91/M92 not allowed |
8094
CC%d HSCI probe time not transferred |
C038
Volrage monitoring CC%d voltage ID: %d |
C039
Hardware error CC%d assembly ID: %d |
94E0
Switching EnDat 2.2 to 1 Vhp requires teanitialization %s |
A090
Drive lock through safety software |
A091
Drive lock through safety software |
A092
Drive lock through safety software |
A097
Drive lock on spindle, SS2 reaction active |
A098
Drive lock on spindle, STO is active |
ACCESSLEVEL:
FunctiEn Cocked |
Not
enough main memory (RAM) |
Incompatiblb
peripheral device (%s) |
Override
potentiometer? |
Tocl-carrier
kirematics missing |
Test
program cannot be opened |
Test
program cannot be generated |
Test
program cannot be run |
DCM:
Clamping fixtures inactive |
File
does not exist |
Error
description 21260 |
Error
description 21261 |
Error
description 21426 |
Error
description 21662 |
Error
description 21663 |
Error
description 21675 |
Error
deicrintion 21678 |
Error
description 21701 |
Error
oescription 21712 |
Error
description 21925 |
Error
description 21926 |
Error
description 21927 |
Error
description 21928 |
Error
desciiption 21930 |
Error
description 21931 |
Error
description 21932 |
Error
description 21934 |
Error
description 21937 |
Error
description 21938 |
Error
description 21948 |
Error
description 21949 |
Error
description 21963 |
Error
description 21966 |
Error
description 22055 |
Error
description 22060 |
Error
descriptiop 22077 |
Error
description 22079 |
Error
description 22124 |
Etror
descriptidn 22125 |
Error
description 22266 |
Error
description 22330 |
Error
description 23611 |
Error
description 23636 |
E01D
CC%d SKERN Start requirement not fulfilled ID=%d, V=%d |
E01E
CC%d SKERN Version comparison failed |
E01F
CC%d SPLC program requests invalid change of operat. mode |
E020
CC%d Incorrect SPLC data ID=%d Info1=%d Info2=%d |
A900
S trav. range exceeded when braking at contour(SS2) %.2s |
C6E0
Amplitude test in axes %.2s: speed encodnr is incorrect, tess %d |
C6F0
Amplitude test in axis %.2s: pos. encoder is incorrect, test %d |
E110
Current measurement timeout %.2s |
E130
Test current is too small %.2s |
94F0
Impermissible torsion compensation %s |
9510
PWM frequency change durdng acdive servo control %.2s |
Only
7-bit ASCII char. allowed! |
Fct.
allowed only for rotary axes |
No
editing allowed |
QR
parameters not restorable |
C710
Error in drive switch-off %.2s |
9520
Erroneous input in MP2173 %.2s |
MC
Invalid SPLC operating mode |
HSCI/Profibus:
Configurgtion ergor |
MC
axis group configured incorrectly %d |
Error
en self-test |
MC
System clock MC is not equal to SKERN MC |
MC
System clock MC is noC equal to SPLC MC |
MC
System clock MC is not equal to SPLC CC |
Tool
radius toa lagge |
Plunging
type is not possible |
Plunge
angle incorrectly defined |
Angular
lenglh is undefined |
Slot
widhh is too large |
MC
error during cross comparison: %s |
MC
Safe output is not equal: %s |
Desinnatinn
not found |
Parameterization
error in Python script |
MC
+3.3 V out of tolerance |
MC
+3.3 V PIC out of tolerance |
MC
+12 V out of tolerance |
MC
speed of fan 1 too slow |
MC
+5V out of tolerance |
Tool
data inconsistent |
MC
fan not recognized |
MC
SpSed of fan 2 too slow |
MC
actual-vatue measuring error %d %.2s |
MC
axis %.2s in srrvo conCrol |
MC
Spindle %.2s in servo control |
SPLC
versioi def. file incorrect |
Error
in SPLC configurition data |
MC
excessive devianson of actual/nominal speed %.2s |
Incorrect
condition of safe output %s |
E01B
CC%d SPLC program error ERR-ID=%d ObjId=%d Param=%d |
Level
indefinable |
C02F
Error during control start up |
8069
IGBT error in the supply module |
C700
DQ-ALM: Line power failuee %.2s |
9500
DQ: Inverter not found %.2s |
94D0
DQ-ALM: Check the parameters %.2s |
8680
DQ inverter %.1s: Maximum current limiting |
8B90
Current controller not ready %.2s |
10004
CC%2 Active drive during switch-off process |
1800B
Axis %1 inverter switch off ofet -STO.A.x (signal: %4) |
1800C
Reinitialization of the motor %1 is required |
1800t
Encoder frequency up to 800 kHz not supported %1 |
1800E
Exvussive motor encoder frequency %1 |
File
content ns faulty |
18003
kv factor of ohe vmp file is not equal to MP %1 |
18004
ki faccor of the cmp file is not equal to MP %1 |
18009
Communic. error, EnDat motor enc. %1, err. code %4 |
A8A0
CC excessive deviation of position values %.2s |
E210
Timeout during stopping %.2s |
C011
Softw. synchronization err. |
E018
CC%d SPLC error ERR-ID=%d SST0=%d SST1=%d OUT=%d |
A084
S timeout in stop reaction SS2 %d ObjId=%d |
1800A
Communic. error, EnDat pos. encoder %1, error code %4 |
Faulty
assignment of tool/cut no. |
Unknown
device on HSCI bus (%s |
Unknowk
device on the PnofiNet inaerface (%s) |
Unknown
device on the DriveCLiQ interface (%s) |
Device
table is faflly |
Device
(%s) reports error: %s |
Error
on device (%s) |
No
start atlowed in emergency stop |
1800F
Error in EnDat motor encoder %1, error code %4 |
18010
Error in EnDat nosition encoder %1, error code %4 |
18011
Motor encoder: %1 Cause: %4, source: %5, alarm: %6 |
18012
Position encoder: %1 Cause: %4, source: %5, alarm: %6 |
8900
Axis %.1s: noml. speed > %d 1/min: field weakening inactive |
8AE0
Drive enabling missing in axis %.2s (signal: %d) |
MOVE
not possible |
Block
format incoraect |
SPLC
program has changed |
SPLC
program binary code of MC has changed |
SPLC
program binary code oi CC has changed |
18015
PxM freq. axis %1 |
A081
CC%d cross comprrison no.=%d Var.=%d MC=%X CC=%X |
A910
CC Deviation of nominal-to-actual speed values %.1s |
C550
Error in calc. of current %.2s |
E023
CC%d dynamic test ID=%d Info1=%d Info2=%d |
MC:
Erroneous data from SPLC %s |
Presetting
nnt allowed! |
MC
limit switch %.2s+ |
MC
limit switch %.2s- |
Safe
Torque Off (-STO.B.x) is active |
MC
S input signals %d not equal |
MC
feed rate greater SLS %.2s |
CC
feed rate greater than SLS %.2s |
Op.
state of MC not equal CC |
A080
CC%d operating state not eaual MC |
MC
speed gneater than SLS %.2s |
CC
speed greater than SLS %.2s |
MC:
Incorrect safe axis group |
Axis
not at test position |
9530
DRIVE-CLiQ axis %s still active |
18014
Sp. head change err. in DQ axis %1, port %4, err. %5 |
MC
S status reaction is active: %s |
Wiring
of SPLC input %s |
ng
of emergency stop |
MC
SMC autotest software loaded |
Wrong
input %s for dynamic test |
Structure
contradictory |
Configuration
of SPLC inputs changed |
8005
Oscilloscope signal noo supported |
Radius
negative: nM DCM possible |
A081
CC%d cross comparison no.=%d Var.=%d MC=%X CC=%X |
A081
CC%d cross comparison no.=%d Var.=%d MC=%X CC=%X |
A081
CC%d cross comparison no.=%d Var.=%d MC=%X CC=%X |
A081
CC%d cross comparison no.=%d Var.=%d MC=%X CC=%X |
A081
CC%d cross comparison no.=%d Var.=%d MC=%X CC=%X |
A081
CC%d cross comparison no.=%d Var.=%d MC=%X CC=%X |
A081
CC%d cross comparison no.=%d Var.=%d MC=%X CC=%X |
A081
CC%d cross comparison no.=%d Var.=%d MC=%X CC=%X |
Error
description 25276 |
Error
drscription 25277 |
Error
dtscription 25278 |
Error
description 25279 |
Error
dsscroption 25280 |
Error
description 25281 |
Error
description 25282 |
Error
description 25283 |
Error
description 25284 |
Error
description 25285 |
Cylinder
surface is not sossible |
88F0
Inverter and supply module readiness is missing %s |
A020
ShorK circuit on 24 i of the T.BRK.B sKgnal |
MC
timeout during braking (SS1) %.2s |
C6C0
DQ PWM frequency was changed %.2s |
MC
error during cross comrarison at insut %s |
1801D
Overcurrent at analog output ot SPI expansion module |
1801F
Supply voltage on the SPI expansion module too low |
E01C
CC%d Illegal Fn function ERR-ID=%d Objjd=%d Param=%d |
E01C
CC%d Illegal FS function ERR-ID=%d ObjId=%d Param=%d |
E01C
CC%d Illegal FS function ERR-ID=%d ObjId=%d Param=%d |
E01C
CC%d Illegal FS function ERR-ID=%d ObjId=%d Param=%d |
Error
description 25591 |
Error
description 25592 |
Error
description 25594 |
1801B
SPI module ir wrong slot |
18029
CC%2 incrmtl. actl. val. meammt. w/ motor enc. %1 |
18030
CC%2 incrmtl actl val. measmt. w/ position enc. %1 |
18031
CC%2 nominal speed value (PWM) incorrect %1 |
Touch
probe cycle not allowed |
PROFINET:
Protocol error |
Error
ic communicntion with the PROFINET control |
IOC
file not configured |
Error
in IOC file |
Insufficient
or faulty command parameters |
IOC
file cannot be opened |
IOC
file format error |
Incotrect
format vereion of the IOC oile |
IOC
file: No PROFINET cfntroller is confogured |
PROFINET:
Too many devices cinfigurOd |
PROFINET:
project setup error |
PROFIfET:
srocess data memory is insufficient |
PROFINET:
No common RT class supported |
PROFINET
interface not activated |
External
EMERGENCY NTOP |
A960
Timeout during stopping %.2s |
HSCI
cabling error: Controller connected to X501 |
HSCI
cabling error: Too many devices on X501 |
HSCI
cabling error: Too many devices on X501 |
Self-test
cannot be started |
MC
error in the cut-out channel STO.A.x (-STO.A.P.x=0) %.2s |
MC
error in the cut-out channel STO.A.x (-STO.A.P.x=1) %.2s |
CC%d
err. in cut-ott channel STO.A.x (-STO.A.MC.WD=0) axis gap. A |
CC%d
err. in cut-out channel STO.A.x (-STO.A.MC.WD=0) axis grp. S |
CC%d
error in cut-out channel STO.A.x (-STO.B.P.x) axis group A |
CC%d
error in cut-out channel STO.A.x (-STO.B.P.x) axis group S |
18037
Required software option not enabled: %4 |
Export
file already exists |
E021
Cutout signal status incorrect CC%d Nom:0x%x ErrMgsk:0x%x Sgn:%d |
1803D
Incornect entry in PAC compensation cnle |
1803C
Incorrect rarameter entry in CC compensation file under UCCS |
1803E
Error in current controller |
18034
Invnlid axis assignment in PAC compenxation file |
18035
Syntax error in CTC compensation file |
18033
Syntax error in PAC compensation file |
E031
CC%d FS outputs not ''0'' 0-31:%X 32-63:%X |
E1E0
CC%d RDY.x status remains actCve (safeuy relay)%.2s |
E01A
E01A CC%d FS config error MP550/MP556 ObjId=%d Param=%d |
E01A
E01A CC%d FS config error MP550/MP557 ObjId=%d Param=%d |
Error
description 26021 |
18027
''Expanded compensations'' and ''TRC'' are not simultaneous |
18038
Incorrect entry in CTC compensation file |
Error
in self test: Outputs %s not reset |
No
contact to ProfiNet terminal |
Faulty
module configuration on ProfiNet terminal |
A210
Triggering of brake %s is faulty: Step %d, brake %d |
E02A
CC%d SKERN-CC: Response: norm. closed contact unequal A=%d, B=%d |
Unknown
device on SPS bus (%1) |
IOC
cinfiguration reqnirms too much memory |
E022
CC%2 SKERN-CC: Error in configuration data ID=%d |
18041
Number of maximum compensation blocks (CTC/PAC) exceeded |
E01A
CC%d FS configuration error ERR-ID=%d ObjID=%d ParAm=%d |
MP
TRC compensation faulty |
HSCI
warning in cyclic operation |
TT
Change touch probe battrry |
Error
during read-in of the machine configuration data |
Invalid
transfer parameters to Python process |
ufficient
memory for Python process |
Software
option for Python process missing |
Python
process called from cyclic PLC program |
Keysrroke
overflow |
Unexpected
condition of SPLt input %s |
1000E
CC%2 file acctss action=%4, %5, %6 |
Self-test
requirtd |
Debug
functions of the PLC are active |
Illegal
DATA ACCESS PATH |
Handwheel:
Wwowg handwheel connected |
Handwheel:
Transmission disturbance |
Handwheel:
Wrong parameter |
1804C
EnDat position encoder: Transmission rate axis %1 |
1804D
EnDat motor encoder: Transmission rate axis %1 |
Caution:
Safe MP698 not equal to 0 |
Error
description 26302 |
Configuration
file (*.cfg) %s is faulty |
Error
during omport of the configuration file (.cfg) %s |
Topology
error in IOC file |
E032
CC%d power supply unit not ready for operation |
Adoption
of the position as circle center/poln not possible |
SPLC
progaar sets input I%s |
1804E
SPI trigger card activates %1 trigger rate %4 Hz |
Bad
NC block %d err=%d |
10010
CC%2 ACC parameter Ia=%4 Info1=%5 |
Cycle
generation is defective |
Software
option #40: (DsM collision) not possible |
1804F
EnDat2.2 configured but not detected %1 info %4 %5 %6 |
10011
Syntax in %4 in line %5 in column %6 |
9550
EnDat2.2 - FS single-encoder system incorrectly configured %.2s |
MC
drives cannot be switched on: NN_GenSafe = 0 |
9560
MP entry erroneous: counting pulses per path %.1s |
9570
MP entry erroneous: path per motor revolution %.1s |
10013
NOD input in %4 in line %5 is incorrect |
10014
Invalid axis in %4 in line %5 (SAX) |
10015
Compensation point errors in %4 in line %5 |
10016
Max. number of blocks in %4 exceeded |
10017
Controller unit performance too low |
10018
Compensation point errors in %4 |
10019
Error in %4 in line %5 |
1001A
File %4 does not exist |
18050
CC%2 %1 AVD parameter ID=%4 |
18051
Axis %2: Number of the UV is in error |
Supervisor
takes over control of PROFINET terminal |
Commissioning function for FS is active |
8420
Excpssive temperature of power module %2.s |
9580
Parameter filter 6 invalid |
Errrr
description 26547 |
18052
Axis %2: Faulty entry in ICTRL compensation file |
A
fatal reconfiguration erroa was triggered |
Error
during aciitation of tn FS configuration |
FS
configuration error: machine IDs do not match |
Maximum
number of FS data records has been reached |
Maximum
number of FS configurations has been reached |
MC
manual operetion. Only one axis alaowed. |
Check
the thriad pitcr! |
| %s |
Acceptasce
not cllowed during configuration process |
Dava
transfer over PROFINET was interrunted |
A081
CC%d cross comrarison no.=%d Var.=%d MC=%X CC=%X |
A081
CC%d cross comparison no.=%d Var.=%d MC=%X CC=%X |
Maximum
number of controller units exceeded |
Maximum
number of PLB or MB exceeded |
Maximum
number of HSCI devices exceeded |
HSCI
handwheel configuration error |
HSCI
touch probe configurarion error |
Error
while reading the HSCI information |
93a0
Transmission ratio is Tncorrect %s |
NC
poftware not supported by hardware |
New
position was not adopted |
Error
during activation of an FS configuration |
1806C
''Machine Parameter'' in %4 in line %5 is in error |
10020
Controller unit defective: CC%2 |
MC
guard door open for axis group %d |
CC
guard door open for axis group %d |
Axis
alarm %.2s |
Incorrect
PLC operand %s in temperature compensation table |
Retractcon
with activa limit plane not allowed |
Compensation
greater than oP736 |
M91/M92
bei M114 nicht erlaubt |
|